English
Deutsch
Nederlands
Parts & pieces
couplings, valves, solenoids, splitters, tubing, air horn supports, membranes-, or diaphragms, shields-, or snow caps etcetera.
About the couplings: Fortunately Napoleon did not conquer the whole world. Unfortunately enough... that left the world with a wide variety of ways to measure stuff and a mind-boggling number of threadings.
To indicate the measurement; we have marked each product with either: (US) for US measurement standards, or (EU), for the metric system.
Oh and don't worry; if it's not listed below, just ask.
Loading...
Hadley H00927. Snow cap for the regular Hadley truck horn types such as the H00855 and the H00856. Polished shield with 15cm diameter
Hadley H00928B. Snow cap for the large 868 air horn type. Polished shield with 20cm diameter
Valve set for Hadley Air horns with M12 inlet. Complete set of couplings, tubing electro valve for Hadley air horns with M12 inlet.
Hadley regular air horn support for truck horns. This regular horn support is mostly used for the H00856 and H00855, as well as the rectangular Ambassador- and aluminium Hadley truck horns.
Hadley Medium air horn support for truck horns. This horn support is mostly used for the H00861 and E-tone horns.
Hadley Air horn support for the 95cm long 868 truck horns. The large air horn support for Hadley (or other) air horns.
Hadley diaphragm kit. Replacement set for your Hadley diaphragm, or membrane. Set includes also new rubbers, nuts and bolts and new "torx" screws to fasten the back of the membrane housing.
Brass adaptor with 7/16-24 UNF Female inlet, to European 1/8 BSP Female inlet.
Brass adaptor made to fit, Hadley horns with 7/16-24” threaded inlet, to European pneumatic systems. Female end with 1/8 BSP/Gas thread.
Brass adaptor M12x1.5 male to 7/16"-24UNF female. Specifically turned to fit US size couplings and air systems to Hadley Air horn with a M12x15 inlet.
Special coupling for the classic Kockum Air Tyfon. This coupling fits in the classic membrane housing of older types Kockum Air horns. Male 7/8"-14UNF - Female 3/8" BSP.
Splitter for 6mm tubing. Three openings with "Push to Connect" inserts.
Straight coupling for 6mm tubing. This coupling has 1/8" short thread. Because of this short thread it wil fit in both NPT- as BSP threaded inlets. Can be used in combination with 7/16"-24 adapt
Straight coupling for 8mm tubing. Because of the short thread it wil fit in both NPT- as BSP threaded inlets. Can be used in combination with 7/16"-24 adaptor.
Angle coupling for 6mm tubing. This coupling has 1/8" short thread. Because of this short thread it wil fit in both NPT- as BSP threaded inlets. Can be used in combination with 7/16-24 adaptor.
Angle coupling for 8mm tubing. This coupling has 1/8" short thread. Because of this short thread it wil fit in both NPT- as BSP threaded inlets. Can be used in combination with 7/16"-24 adaptor.
Straight coupling for 6mm tubing. This coupling has M12x1,5 threading. Ideal for connecting Hadley air horns with M12 threading.
Straight coupling for 8mm tubing. This coupling has M12x1,5 thread. Ideal for connecting Hadley air horns with M12 thread.
Angle coupling for 6mm tubing. This coupling has M12x1,5 threading. Ideal for connecting Hadley air horns with M12 threading.
Angle coupling for 8mm tubing. This coupling has M12x1,5 thread. Ideal for connecting Hadley air horns with M12 thread.
The H00755VE; the lanyard that can be installed remotely from your airhorns. The valve includes tighten fittings for 1/4" size air tube.
The H00755NS is the lanyard valve that can be directly screwed into Hadley air horns with a 7//16"-24 threaded inlet. The valve includes a tighten fitting for 1/4" size air tube.
Fiamm electric solenoid valve for vehicles with 24v electrical system. This solenoid valve comes with 1/8 threaded inlet and outlet. For both ends tighten fittings for 6mm air tube are included.
Normally closed electro valve 12 and/or 24v DC. Inlet 3/8" tubing. Outlet 1/4" tubing. Working pressure 0-10 bar.
Normally closed electro valve 24v DC. In-and outlet 3/8 BSP. Opening Ø10mm. Working pressure 2-10 bar.
Normally closed electro valve 220/230v AC. In-and outlet 3/8 BSP. Opening Ø10mm. Working pressure 2-10 bar.
Straight coupling for 10mm tubing. This coupling has 3/8" short threading. Because of this short threading it wil fit in both NPT- as BSP threaded inlets. This coupling can be used in combination with
Straight coupling for 8mm tubing. This coupling has a 3/8" short thread. Because of this short thread it wil fit in both NPT- as BSP threaded inlets. This coupling can be used in combination wit
Straight coupling for 8mm tubing. This coupling has 1/8" short thread. Because of this short thread it wil fit in both NPT- as BSP threaded inlets. This coupling can be used in combination with
Straight coupling for 6mm tubing. This coupling has 1/4" short threading. Because of this short threading it wil fit in both NPT- as BSP threaded inlets. This coupling can be used in combination with
Normally closed electro valve 12v DC. In-and outlet 3/8 BSP. Opening Ø10mm. Working pressure 2-10 bar.
Lanyard valve Large, normally-closed,, operates from 0bar up to 10bar pressure, input & output has 1/4" BSP thread.
Pressure switch for compressor sets. Switching on at 90psi (6 bar). Shuts off at 120psi (8 bar). Supplied as standard on VIAIR set 20003.
Extended angle coupling with fitting for 1/4 inch hose and 7/16-24 UNF male thread. For Hadley air horns with 7/16 thread connection.
Straight screw-on coupling PTC for 8 millimeter tube to 1/8 BSPP female
Straight screw-on coupling PTC for 6 millimeter tube to 1/8 BSPP female
Adapter for 1/8 NPT to 1/8 BSPP. With 1/8 NPT male to 1/8 BSPP female.
Adapter for 1/8 BSP to 1/8 NPT. With 1/8 BSPP male to 1/8 NPT female.
Quick connector with 1/8 BSP female connections. For quick connecting- or releasing pneumatic systems without pressure loss at the air source. 1/8 BSP female thread on both sides.
Adapter for 1/4 NPT to 1/4 BSPP. With 1/4 NPT male to 1/4 BSPP female.
Adapter for 1/4 BSP to 1/4 NPT. With 1/4 BSPP male to 1/4 NPT female.
Adapter for 3/8 BSP to 3/8 NPT. With 3/8 BSPP male to 3/8 NPT female.
Adapter for 3/8 NPT to 3/8 BSPP. With 3/8 NPT male to 3/8 BSPP female.
Quick connector (EURO system) with 1/4 BSP female connections. For quick connecting- or releasing pneumatic systems without pressure loss at the air source. 1/4 BSP female thread on both sides.
Quick connector (ORION system) with 1/4 BSP female connections. For quick connecting- or releasing pneumatic systems without pressure loss at the air source. 1/4 BSP female thread on both sides.
Hadley seal for Hadley horns with empty PTC inlet. Complete set to connect 6 mm tube directly to Hadley horns with inlet without thread, or plug-in coupling. (NOTE: Only empty PTC)
Special brass reducing nipple, or adapter for 7/16-24 UNF male thread to 1/8 BSP female thread. Specially suitable for Hadley air horns with American inlet.
Hadley electronic valve for mounting on air horn with 1/4 NPT thread. The H00550C is especially for air horns with a 1/4 NPT (threaded) entry.
Hexagonal brass Hadley nut for 7/16-24 thread. Set of 5 Used for American connections with a 7/16 male thread.
Hadley Snow Cap, or Shield. 175mm diameter. Suitable for Hadley air horns type H00861 and E-tones H09318AC, H09321AC, H09324AC. Polished Stainless Steel.
Right angle plug-in coupling with PTC connection for 6 mm. This right-angled coupling can be plugged into another PTC connection with the 6mm pin. Suitable for Hadley horns with 6mm PTC connection.
Right angle plug-in coupling with PTC connection for 6 mm. 44 mm This right-angled coupling can be plugged into another PTC connection with the 6mm pin. Suitable for Hadley horns with 6mm PTC connecti
Plug-in coupling with PTC connection for 8 mm tube. This coupling can be plugged into another PTC connection with the 6mm pin. Suitable for Hadley horns with 6mm PTC connection.
Pin for 6mm plug-in coupling. Double-sided plug with a diameter of 6mm. Both sides can be plugged into a 6mm 'Push to Connect' connection.
Pull valve with cord. Valve with connection for 6mm tube. Supplied with cord and compression fittings for 6mm tube. Male thread on couplings is 1/8 BSPP (gas).
Brass adapter M12 to 7/16 UNF. Special brass adapter to convert M12x1.5 (EU) to 7/16-24 UNF (US). Extended adapter M12x1.5 to 7/16 UNF.